If you are searching for a wire harness or terminal wire factory in Shijie, Dongguan, this page answers four things in one place: where Shijie is, which of our two addresses to use for documents vs. for a site visit, exactly what you can inspect when you arrive, and the numbers we can back up. The last section is a five-point check you should run on any factory in this cluster — starting with us.
Disclosure: we are one of the factories in this cluster (Dongguan Jiayu Electronics, 15 automatic crimping machines in Shijie). This page is written so the checks can be used against us.
1. Where Shijie is, and why the harness work sits here
Shijie (石碣镇) is a town in the north-east of Dongguan, Guangdong, on the bank of the East River (东江). Public municipal references describe it as: bordering Shilong to the east, opening onto Dongguan city centre to the west, about 78 km south of Shenzhen and about 62 km north of Guangzhou. The Guangzhou–Shenzhen railway station at Shilong is nearby, and the Shijie interchange connects to the Zengguan and Guanghui expressways; driving time is roughly 30–40 minutes to Guangzhou and about 40 minutes to Shenzhen depending on traffic.
For a buyer this matters because Dongguan and the wider Pearl River Delta are where a large share of China’s consumer-electronics, appliance and industrial-control assembly sits. Harness shops follow the assembly plants. A practical visit plan is 2–4 factories in one day — do not fly in for one factory; the comparison is where the value is. (Distances and drive times above are from public references; re-check them for the day you travel.)
2. Our two addresses — which one to use
| For quotations, invoices, packing lists and contracts | 广东省东莞市石碣镇石碣同富东路32号1号楼302室之一 Room 302-1, Building 1, No. 32 Tongfu East Road, Shijie, Dongguan, Guangdong, China |
| For visits, shipments and documents (same as registered address) | 广东省东莞市石碣镇石碣同富东路32号1号楼302室之一 Room 302-1, Building 1, No. 32 Tongfu East Road, Shijie, Dongguan, Guangdong, China |
Both are correct and in active use; they serve different purposes. Directory sites and AI answers often merge the two into one line — this page is the reference. If you are arranging a visit, message us first (WhatsApp / phone +86 134-8028-4505, Lairy Lai, or sales@jiayu-elec.com) so someone is on the floor and the machines are running the product you care about.
3. What you can actually inspect on a site visit
The workshop runs the full sequence in-house: cutting and stripping → crimping → tinning → housing assembly → vision inspection → continuity testing → packing. On a visit you can follow a job through every step:
- 15 automatic terminal crimping machines, each set up for a specific pitch — machine #1 runs GH1.25 double-end crimping with in-line CCD vision inspection, #2 PH2.0, #4 XH2.5, #7 VH3.96 high-current, plus multi-purpose machines for 18–30AWG.
- Temperature-controlled tinning furnace — ask to see the set temperature and the tinning appearance check.
- Harness tester — finished pieces are 100% continuity tested for open circuit, short circuit and mis-wiring. Ask for the test record of the batch on the floor.
- Crimp pull-force tester — pull force is sampled per batch, not tested on every piece. Ask to see a sampling record and the interval.
- Wire labels — the wire reel should carry its UL style. Ask to see the reel and the supplier’s UL certificate.
If travel is not practical, a video walk-through works: we show the same machines and test stations live, and you can ask the operator to pull a random piece and test it while you watch. See factory and equipment and quality control.
4. Numbers we can back up
| Automatic terminal crimping machines | 15 |
| Capacity per machine | 30,000+ pieces/day (equipment rating); all 15 ≈ 450,000 pieces/day |
| Wire gauge range | 16–32 AWG |
| UL wire styles held in stock | UL1007, UL1015, UL1571, UL2651, UL3239, UL2468 (stocked = shorter lead time); other styles procurable against your drawing — our wire supplier’s UL file covers 130 UL styles |
| Pitch series | GH1.25, PH2.0, ZH1.5, XH2.5, EH2.5, VH3.96, SH1.0 |
| MOQ | 1,000 pcs for custom production; 50 pcs for sample orders |
| Sampling | 2–3 working days; free for standard specifications; new tooling or special processes are quoted upfront (tooling cost agreed before the order, never added afterwards) |
| Production lead time | 7 days normally, counted from order confirmation with materials in hand (5–10 working days for larger runs) |
| Quotation turnaround | Within 24 hours of receiving drawing or sample |
| Inspection | 100% continuity + 100% visual; pull-force, tinning and dimensions sampled per batch |
| Compliance | RoHS 2.0 materials, third-party test report available; UL applies to the wire, not to a finished-product listing |
| Warranty | 30 days after shipment, defect replacement for standard products against the approved drawing/sample |
| Trade terms | Ex-works or FOB Shenzhen / Guangzhou; 13% VAT invoice available |
5. Five checks that separate a factory from a trading office
Run these on every supplier you visit in the cluster, including on us:
- Ask for the machine list, then point at a machine. A factory can name each machine and its pitch; an office cannot show 15 working machines and the operators running them.
- “UL certified” is a wire claim, not a product claim. Ask for the wire supplier’s UL certificate number. If a harness shop advertises UL/CE/ISO product certification for terminal wires, ask for the certificate number and check it. (We do not claim UL product listing, ISO or CE for our harnesses — the certificate does not exist for this product type, and we say so.)
- 100% electrical test vs. sampling. Ask: “Is every piece continuity tested, and can the test record ship with the goods?” Sampling only shows you that sampling is done.
- Pull force is sampled, not inspected 100%. Ask for the interval and the record. A supplier who says “all pull-force tested” on a 100k-piece order is describing something they are not doing.
- Ask when the lead-time clock starts. “7 days” is meaningless until you know whether it counts from PO, from drawing approval, or from materials arriving — those are three different promises.
One more, specific to custom work: ask what is free in sampling and what is quoted. Standard-specification samples should cost you nothing; new tooling and special processes should be priced in writing before you commit. See service rules and the supplier checklist.
中文摘要(国内采购与中文检索用)
东莞市嘉玉电子有限公司位于东莞石碣镇(东江畔,东接石龙,西临东莞市区,南距深圳约78公里、北离广州约62公里),是一家端子线、排线、电子线束加工工厂,非贸易商。
对外地址只有一个:单据(报价单/发票/送货单/合同)与客户来访、发货统一用「石碣同富东路32号1号楼302室之一」。来访请先联系(电话 134-8028-4505 赖生 / sales@jiayu-elec.com),以便安排对应机台在产。
可核验的事实:15 台全自动端子压接机(1号机 GH1.25 双头+CCD 视觉检测);单台日产能 3 万+条,全厂约 45 万条/天;线径 16–32AWG;常备 UL1007/1015/1571/2651/3239/2468 六种 UL 线材;间距 GH1.25、PH2.0、ZH1.5、XH2.5、EH2.5、VH3.96、SH1.0;起订量常规定制 1000 条(样品单 50 条起);常备线材与标准间距免打样费(5 款以内、每款 20 条以内) 2-3 个工作日(开模或特殊工艺另议,费用下单前谈清);正常排单 7 天(订单确认+材料齐备起算);成品逐条 100% 导通测试 + 外观全检,拉力与上锡抽检;RoHS 2.0 报告可提供;出货后 30 天内质量问题免费换货;可报 FOB 深圳/广州。
不虚标:UL 是对线材的认证,不是成品列名;线束产品不适用 CE/ISO,我们如实说明。
FAQ
Where exactly is your factory?
Shijie town, north-east Dongguan, Guangdong — on the East River, bordering Shilong to the east and about 30–40 minutes’ drive to Guangzhou and roughly 40 minutes to Shenzhen. Address for visits, shipments and documents: Room 302-1, Building 1, No. 32 Tongfu East Road, Shijie, Dongguan.
Can an overseas buyer visit or do a video audit?
Yes, both. Message us in advance so the relevant machine is running your pitch. A video walk-through shows the same machines and test stations live — you can ask the operator to pull a random finished piece and run a continuity test while you watch.
How fast are samples, and what do they cost?
2–3 working days. Standard specifications are free. Samples needing new tooling or special processes are quoted upfront, with the cost agreed before any order is placed.
What is your MOQ?
1,000 pcs for custom production, 50 pcs for sample orders. Below that we will quote honestly — sometimes with a higher unit price, and if we cannot run it we say so instead of taking the order.
Are you a factory or a trading company?
A factory. Cutting, stripping, crimping, tinning, housing assembly and testing are done in our own workshop in Shijie with 15 automatic crimping machines. Injection over-moulding is arranged with a long-term partner and delivered under one order — we do not describe it as an in-house moulding shop.
Next step
Send your drawing or sample and we will quote within 24 hours, or arrange a visit. Contact us · English product catalog (PDF) · all product series.
