Terminal Wire Selector – Find the Right Series by Pitch and Application

Three questions decide the series: what pitch your board or mating connector uses, how much current the wire carries, and what environment it runs in. Use the filters below to narrow our series by pitch and application, then open the series page for full specifications, MOQ, lead time and datasheet download.




Series Pitch Pins (standard) Wire gauge Typical application
PH2.0 2.0 mm Custom 24–30AWG Home appliances, industrial control panels, LED displays
GH1.25 1.25 mm Custom 28–32AWG LED lighting, small appliances, consumer electronics
XH2.5 2.5 mm Custom 20–28AWG Battery management (BMS), power tools, power supplies
ZH1.5 1.5mm Custom 26AWG – 30AWG LED display modules, precision instruments, security cameras, small appliances
VH3.96 3.96mm Custom 16AWG – 22AWG Power adapters, chargers, high-current appliance sections, LED power
JST 2.54 2.54mm 2 24AWG LED strips, lithium battery packs, small appliances, signal links
SH1.0 1.0mm 2/8 To drawing Battery packs, drone flight controllers, heater pads, small appliance boards
MX3.0 3.0mm 2 18AWG PC motherboards, power adapters, GPU/HDD power, internal device power
HY2.0 2.0mm 2/6 22/24AWG Smart locks, LCD modules, board-to-board links, smart appliances
SM 2.54 2.54mm 2/4/5 To drawing Automotive electronics, security devices, industrial signals, LED fixtures
XHS / XHB 2.54mm 1-16P 20AWG Drone displays, relay control, switching power supplies, indicator lights
SCN 2.54 2.54mm 2 24/30AWG Automotive ignition/engine wiring, board-to-board, industrial equipment, sensors
Dupont 2.54 2.54mm 1/2/3 22/24/28/30AWG Breadboards and test fixtures, RC receivers, dev boards, lab equipment
5557 2.54mm Custom 18-24AWG Male-female power links, internal power for appliances and equipment
EL4.5 / YL4.5 / VL6.2 / SL4.2 4.5-6.2mm 2 22AWG High-current power links, LED fixtures, appliances, motors and fans
Spade 187 / 250 4.8/6.3mm 1-16P 10/18/20AWG Appliance internal wiring, control cabinets, motors, switches and thermostats
Ring crimp — 2 26AWG Grounding, battery connections, solar modules, distribution cabinets, storage
Waterproof JWPF 2.2mm 2/3 To drawing Automotive LED lighting, outdoor fixtures, smart home, wet environments
Automotive 28050 / 2510 / 5264 2.5-2.8mm 2 24AWG E-bike and scooter harnesses, automotive devices, controllers, batteries
RC / XT60 / MR30 — 2 To drawing Drone power links, RC models, LiPo packs, ESC and motors
XA male-female 2.5mm Custom 22-30AWG Board-to-board and wire-to-board links, appliance and industrial interiors
Bullet — Custom 24-28AWG Lamps, motors, quick-disconnect power links
SM male-female 2.54mm Custom 24-28AWG Male-female extension links, LED strips, internal device wiring
Custom connectors — 2/4 16/22/24/28AWG Built to customer drawings: special connectors, automation equipment
Silicone (high-temp) — 1-16P 14/18/20/22/28AWG EV charging, heaters and high-voltage gear, RC power, LED
Ribbon UL2651 / 2468 1.27mm 4/8 26/28/30AWG Board-to-board, LED strips, appliance signals, ribbon adapters
FFC flexible 0.5-1.25mm 26 To drawing LCD and backlight, mainboard data, printers and scanners, precision devices
PTFE / electronic wire — 2 22/24/28AWG Speakers, precision electronics, high-temperature routing, signal
Pre-cut & stripped — Custom Custom Pre-cut and stripped leads, ribbon assemblies

How to use this selector

  1. Match the pitch first. Measure the distance between two adjacent pins on the mating header — that number (1.0, 1.25, 1.5, 2.0, 2.5, 2.54, 3.0, 3.96 mm) is the series family. Pitch is not interchangeable: a 1.25 mm housing will not seat on a 2.0 mm header.
  2. Check the current, then the wire gauge. Series tables above give the wire range each family is built for. If your current sits at the top of a range, go up one series rather than up one gauge.
  3. Confirm the environment. Waterproof (JWPF), high temperature (silicone, PTFE) and automotive (28050 / 2510 / 5264) series have different housing and insulation materials from the standard PVC ranges.
  4. Send the drawing. Every series is made to order: pin count, length, colour, single or double end, tinned or open end. Quotation within 24 hours against a drawing or sample.

What we need to quote

  • Connector series or a photo with a ruler / pitch measurement
  • Pin count, wire length, wire gauge and colour
  • Single or double end, tinned, crimped or with housings
  • Quantity per run, and whether samples are needed before the bulk order

Standard terms: MOQ from 1,000 pcs (small orders accepted) · samples in 2–3 working days · bulk lead time 5–10 working days after confirmation · FOB Shenzhen / Guangzhou · custom builds to drawing or sample.

Not sure which series fits? Send us the drawing or a photo and we will confirm the series and quote within 24 hours.

粤ICP备2026110443号-1  |  粤公网安备44195802000145号
滚动至顶部
Privacy Policy | Terms & Conditions | Shipping Policy | Warranty & Returns | Sitemap